..
1 GB/T 324-1988 焊缝符号表示法 Welds-symbolic representation on drawings
2 GB/T 944.1-1985 螺钉用十字槽 Cross recesses for screws
3 GB/T 1031-1995 表面粗糙度 参数及其数值 Surface rougnness--Parameters and their values
4 GB/T 1167-1996 过渡配合螺纹 The threads for transition fit
5 GB/T 1182-1996 形状和位置公差 通则、定义、符号和图样表示法 Geometrical tolerancing--Generalities,definitions,symbols,indications on drawings
6 GB/T 1184-1996 形状和位置公差 未注公差值 Geometrical tolerancing--Geometrical tolerance for features without individual tolerance indications
7 GB/T 1414-1978 管路旋入端用普通螺纹尺寸系列 General purpose screw threads for joints on pipe line--Dimensions
8 GB/T 1415-1992 米制锥螺纹 Metric tape screw thread
9 GB/T 1569-1990 圆柱形轴伸 Cylindrical shaft ends
10 GB/T 1570-1990 圆锥形轴伸 Conical shaft ends
11 GB/T 1801-1979 公差与配合 尺寸至 500mm孔、轴公差带与配合 Tolerance and fitting, dimensions up to 500mm holes, shaft tolerance range and fitting
12 GB/T 1802-1979 公差与配合 尺寸大于 500至3150mm常用孔、轴公差带 Tolerance and fitting, dimensions larger than 500mm andup to 3150mm ordinary holes,shaft tolerance range
13 GB/T 1803-1979 公差与配合 尺寸至18mm孔、轴公差带 Tolerance and fitting, dimensions up to 18mm holes, shaft tolerance range
14 GB/T 1804-1992 一般公差 线性尺寸的未注公差 General tolerances—Tolerances for linear dimensions without individual tolerance indications
15 GB/T 1958-1980 形状和位置公差 检测规定 Rules for inspection of form and position tolerances
16 GB/T 2298-1991 机械振动与冲击 术语 Mechanical vibration and shock—Terminology
17 GB/T 2358-1994 金属材料裂纹尖端张开位移试验方法 Test method for crack-tip opening displacement measurement of metallic materials
18 GB/T 2516-1981 普通螺纹偏差表 (直径1~355mm) Common screw thread deviation table
19 GB/T 3323-1987 钢熔化焊对接接头射线照相和质量分级 Methods for radiographic inspection and classification of radiographs for fusion welded butt joints in steel
20 GB/T 3505-1983 表面粗糙度 术语 表面及其参数 Surface roughness--Terminology--Surface and its parameters
21 GB/T 4096-1983 棱体的角度与斜度系列 Series of angles and slopes on wedges and prisms
22 GB/T 4133-1984 莫氏圆锥的强制传动型式及尺寸 The type and dimensions for positive drive of Morse tapers
23 GB/T 4249-1996 公差原则 Tolerancing principle
24 GB/T 4380-1984 确定圆度误差的方法 两点、三点法 Assessment of departure from roundness--Two-and three-point methods
25 GB/T 4457.4-1984 机械制图 图线 Mechanical drawings--Lines
26 GB/T 4457.5-1984 机械制图 剖面符号 Mechanical drawings--Symbols for sections
27 GB/T 4458.2-1984 机械制图 装配图中零、部件的序号及其编排方法 Mechanical drawings--Item references and its arrangement for assembling drawings
28 GB/T 4458.3-1984 机械制图 轴测图 Mechanical drawings--Axonometric drawings
29 GB/T 4458.4-1984 机械制图 尺寸注法 Mechanical drawings--Dimensioning
30 GB/T 4458.5-1984 机械制图 尺寸公差与配合注法 Mechanical drawings--Indication of tolerances for sizeand of fits
31 GB/T 4459.1-1995 机械制图 螺纹及螺纹紧固件表示法 Mechanical drawings--Representation of screw threads and threaded parts
32 GB/T 4459.2-1984 机械制图 齿轮画法 Mechanical drawings--Conventional representation of gears
33 GB/T 4459.3-1984 机械制图 花键画法 Mechanical drawings--Conventional representation of splines
34 GB/T 4459.4-1984 机械制图 弹簧画法 Mechanical drawings--Conventional representation of springs
35 GB/T 4459.5-1984 机械制图 中心孔表示法 Mechanical drawings--Simplified representation of centre holes
36 GB/T 4459.6-1996 机械制图 动密封圈表示法 Mechanical drawings--Representation of seals for dynamic application
37 GB/T 4460-1984 机械制图 机构运动简图符号 Mechanical drawings--Graphical symbols for kinematic diagrams
38 GB/T 4974-1989 压缩机、凿岩机械与气动工具优先压力 Compressors, rock drilling machines and pneumatic tools—Preferred pressures
39 GB/T 5371-1985 公差与配合 过盈配合的计算和选用 Tolerances and fits--The calculation and selection of interference fits
40 GB/T 5796.1-1986 梯形螺纹 牙型 Metric trapezoidal screw threads—Profile
41 GB/T 5796.2-1986 梯形螺纹 直径与螺矩系列 Metric trapezoidal screw threads--System of diameter and pitch
42 GB/T 5796.3-1986 梯形螺纹 基本尺寸 Metric trapezoidal screw threads--Basic dimensions
43 GB/T 5796.4-1986 梯形螺纹 公差 Metric trapezoidal screw threads--Tolerances
44 GB/T 5847-1986 尺寸链 计算方法 Dimensional chain--Methods of calculation
45 GB/T 5898-1986 凿岩机械与气动工具噪声测量方法--工程法 Measurement of noise emitted by rock drilling machines and pneumatic tools--Engineering method
46 GB/T 6403.1-1986 球面半径 Radii of sphere surfaces
47 GB/T 6403.2-1986 润滑槽 Lubricating grooves
48 GB/T 6403.3-1986 滚花 Knurl
49 GB/T 6403.4-1986 零件倒圆与倒角 Rounding and chamferd of parts
50 GB/T 6403.5-1986 砂轮越程槽 Relief grooves for grinding wheels
51 GB/T 6404-1986 齿轮装置噪声声功率级测定方法 Determination of sound power level for noise emitted by gear units
52 GB/T 6414-1986 铸件尺寸公差 Dimensional tolerances for castings
53 GB/T 6419-1986 潜水焊工考试规则 Regulations for the qualification test of diver-welders
54 GB/T 6444-1995 机械振动 平衡术语 Mechanical vibration--Balancing vocabulary
55 GB/T 6557-1986 挠性转子的机械平衡 The mechanical balancing of flexible rotors
56 GB/T 6558-1986 挠性转子平衡的评定准则 Criteria for evaluating flexible rotor balance
57 GB/T 6567.1-1986 管路系统的图形符号 基本原则 Graphical symbols for piping systems--Basic principles
58 GB/T 6567.2-1986 管路系统的图形符号 管路 Graphical symbols for piping systems--Piping
59 GB/T 6567.3-1986 管路系统的图形符号 管件 Graphical symbols for piping systems--Piping accessories
60 GB/T 6567.4-1986 管路系统的图形符号 阀门和控制元件 Graphical symbols for piping systems--Valves and control regulation actuators
61 GB/T 6567.5-1986 管路系统的图形符号 管路、管件和阀门等图形符号的轴测图画法 Graphical symbols for piping systems--Axonometric representation of graphical symbols for piping, piping accessories and valves etc
62 GB/T 6719-1986 袋式除尘器分类及规格性能表示方法 Classification and specification for bag filters
63 GB/T 7220-1987 表面粗糙度 术语 参数测量 Surface roughness--Terminology--Measurement of surface roughness parameters
64 GB/T 7221-1987 现场平衡设备的说明和评价 Field balancing equipment--Description and evaluation
65 GB/T 7234-1987 圆度测量 术语、定义及参数 Measurement of roundness--Terms, definitions and parameters of roundness
66 GB/T 7235-1987 评定圆度误差的方法 半径变化量测量 Methods for the assessment of departure from roundness--Measurement of variations in radius
67 GB/T 7306-1987 用螺纹密封的管螺纹 Pipe threads where pressure-tight joints are mede on the threads
68 GB/T 7307-1987 非螺纹密封的管螺纹 Pipe threads where pressure-tight jojints are not made on the threads
69 GB/T 7704-1987 Ｘ射线应力测定方法 Residual stress measurement by X-ray
70 GB/T 7920.2-1987 建筑卷扬机术语 Construction winches-Terminology
71 GB/T 7920.4-1987 混凝土机械术语 Concrete machinery--Terminology
72 GB/T 7920.5-1987 压路机和夯实机术语 Rollers and compactors--Terminology
73 GB/T 7920.6-1987 桩工机械术语 Pile driving machinery--Terminology
74 GB/T 7920.7-1987 翻斗车术语 Small dumpers--Terminology
75 GB/T 7920.8-1987 铲运机术语 Serapers--Terminology
76 GB/T 7920.9-1987 平地机术语 Grader--Terminology
77 GB/T 7920.10-1987 混凝土搅拌机械术语 Soil stabilizer--Terminology
78 GB/T 7920.11-1987 沥青混凝土搅拌设备术语 Asphalt mixing plant--Terminology
79 GB/T 7920.12-1987 沥青混凝土摊铺机术语 Asphalt paver--Terminology
80 GB/T 7920.13-1987 混凝土路面铺筑机械与设备术语 Concrete pavement machine and equipment--Terminology
81 GB/T 7920.14-1987 沥青喷洒机术语 Asphalt distributor--Terminology
82 GB/T 7920.15-1987 沥青贮存、熔化和加热装置术语 Asphalt storage, melting and heating units--Terminology
83 GB/T 7920.16-1987 石料摊铺机械术语 Aggregate and chip spreader--Terminology
84 GB/T 7920.17-1987 钢筋加工机械术语 Steel reinforcement (bar) processing machinery--Terminology
85 GB/T 7920.18-1987 装修机械术语 Finishing machinery--Terminology
86 GB/T 8540-1987 振动与冲击隔离器确定特性要求导则 Vibration and shock--Isolators--Procedure for specifying characteristics
87 GB/T 8543-1987 验收试验中齿轮装置 机械振动的测定 Determination of mechanical vibrations of gear units during acceptance testing
88 GB/T 9145-1988 商品紧固件的中等精度 普通螺纹极限尺寸 General purpose screw threads—Limits of sizes for commercial bolt and nut threads—Medium quality
89 GB/T 9146-1988 商品紧固件的粗糙级精度 普通螺纹极限尺寸 General purpose screw threads—Limits of sizes for commercial bolt and nut threads—Coarse quality
90 GB/T 9443-1988 铸钢件渗透探伤及缺陷显示迹痕的评级方法 Methods of liquid penetrant testing and classification of indication for steel castings
91 GB/T 9444-1988 铸钢件磁粉探伤及质量评级方法 The methods for magnetic particle testing and for specifying quality levels of steel castings
92 GB/T 9445-1988 无损检测人员技术资格鉴定通则 Rules for qualification and certification of NDT personnel
93 GB/T 10084-1988 振动、冲击数据分析和表示方法 Vibration and shock--methods for analysis and presentation of data
94 GB/T 10201-1988 热处理合理用电导则 Guides for the rationality of electricity usage in heat treatment
95 GB/T 10609.1-1989 技术制图 标题栏 Technical drawings—Title blocks
96 GB/T 10609.2-1989 技术制图 明细栏 Technical drawings—Item lists
97 GB/T 10609.3-1989 技术制图 复制图的折叠方法 Technical drawings—Folding on documents
98 GB/T 10609.4-1989 技术制图 对缩微复制原件的要求 Technical drawings—Requirements for microcopying
99 GB/T 10820-1989 燃煤生活锅炉热效率 Boilers using coal for daily life-thermal efficiency
100 GB/T 10853-1989 机器理论与机构学术语 Terminology for the theory of machines and mechanisms
101 GB/T 11056-1989 锻造生产能源消耗标准 Energy consumption standard in forging production
102 GB/T 11057-1989 离心式、混流式、轴流式水泵运行管理 Operational management of centrifugal, mixed flow and axial pumps
103 GB/T 11334-1989 圆锥公差 Cone tolerance
104 GB/T 11335-1989 未注公差角度的极限偏差 Limit deviations of angle without tolerance indication
105 GB/T 11336-1989 直线度误差检测 Measurement of departures from straightness
106 GB/T 11337-1989 平面度误差检测 Measurement of departures from flatness
107 GB/T 11347-1989 大型旋转机械振动烈度现场测量与评定 Mechanical vibration of large rotating machines with speed range from 10 to 200 r/s—Measurement and evaluation of vibration severity in situ
108 GB/T 11349.1-1989 机械导纳的试验确定 基本定义与传感器 Experimental determination of mechanical mobility—Basic definitions and transducers
109 GB/T 11349.2-1989 机械导纳的试验确定 用激振器作单点激励测量 Experimental determination of mechanical mobility—Measurments using single-point translation excitation with and attached vibration exciter
110 GB/T 11349.3-1992 机械导纳的试验确定 冲击激励法 Experimental determination of mechanical mobility--Measurements using impact excitation
111 GB/T 11852-1989 圆锥量规公差与技术条件 Tolerances and specification of taper gauges
112 GB/T 12212-1990 技术制图 焊缝符号的尺寸、比例及简化表示法 Technical drawings—Dimensions, proportions and simplified representation for welding symbols
113 GB/T 12213-1990 技术制图 玻璃器具表示法 Technical drawings for glassware
114 GB/T 12359-1990 梯形螺纹 极限尺寸 Limits of sizes for metric trapezoidal screw threads
115 GB/T 12360-1990 圆锥配合 Cone fit
116 GB/T 12471-1990 木制件 公差与配合 Limits and fits for products of wood and wooden materials
117 GB/T 12472-1990 木制件表面粗糙度 参数及其数值 Surface roughness—Parameters and their values for wooden pieces
118 GB/T 12604.7-1995 无损检测术语 泄漏检测 Terminology for nondestructive testing--Leak testing
119 GB/T 12604.8-1995 无损检测术语 中子检测 Terminology for nondestructive testing--Neutron testing
120 GB/T 12604.9-1996 无损检测术语 红外检测 Terminology for nondestructive testing--Infrared testing
121 GB/T 12716-1991 60°圆锥管螺纹 Taper pipe threads with 60 degree
122 GB/T 13125-1991 机械工业产品湿热带防护包装方法通则 General rule for damp heat protective packaging methods of machinery products
123 GB/T 13126-1991 机械工业产品湿热带防护包装通用技术条件 General specification for damp heat protective packaging of machinery products
124 GB/T 13319-1991 形状和位置公差 位置度公差 Geometrical tolerance—Positional tolerancing
125 GB/T 13321-1991 钢铁硬度 锉刀检验方法 The method of hardness testing on iron and steel with file
126 GB/T 13325-1991 机器和设备辐射的噪声 操作者位置噪声测量的基本准则 (工程级) Noise emitted by machinery and equipment--Guidelines for the preparation of test codes of engineering grade requiring noise measurements at the operator's or bystander's position
127 GB/T 13361-1992 技术制图 通用术语 Technical drawings—General terms
128 GB/T 13362.1-1992 机械制图用计算机信息交换常用长仿宋字体、代(符)号 基本集 Common long fangsongti letterings and symbols in mechanical drawings and computer for information interchange—Basic set
129 GB/T 13362.2-1992 机械制图用计算机信息交换常用长仿宋字体、代(符)号 16×16点阵字模集 Common long fangsongti letterings and symbols in mechanical drawings and computer for information interchange—16×16 Dot matrix font set
130 GB/T 13362.3-1992 机械制图用计算机信息交换常用长仿宋字体、代(符)号 16×16点阵字模数据集 Common long fangsongti letterings and symbols in mechanical drawings and computer for information interchange—16×16 Dot matrix font data set
131 GB/T 13362.4-1992 机械制图用计算机信息交换常用长仿宋矢量字体、代(符)号 Vector common long fangsongti letterings and symbols in mechanical drawings and computer for information interchange
132 GB/T 13362.5-1992 机械制图用计算机信息交换常用长仿宋矢量字体、代(符)号 数据集 Vector common long fangsongti letterings and symbols in mechanical drawings and computer for information interchange—Data set
133 GB/T 13362.6-1993 机械制图用计算机信息交换常用长仿宋字体、代(符)号 24×24点阵字模集 Common long fangsongti letterings and symbols in mechanical drawings and computer for information interchange--24×24 Dot matrix font set
134 GB/T 13362.7-1993 机械制图用计算机信息交换常用长仿宋字体、代(符)号24×24点阵字模数据集 Common long fangsongti letterings and symbols in mechanical drawings and computer for information interchange--24×24 Dot matrix font data set
135 GB/T 13576.1-1992 锯齿形(3°、30°)螺纹 牙型 Butterss threads with 3 and 30 degrees flank angle—Profiles
136 GB/T 13576.2-1992 锯齿形(3°、30°)螺纹 直径与螺距系列 Buttress threads with 3 and 30 degrees flank angle—General plan
137 GB/T 13576.3-1992 锯齿形(3°、30°)螺纹 基本尺寸 Buttress threads with 3 and 30 degrees flank angle—Basic dimensions
138 GB/T 13576.4-1992 锯齿形(3°、30°)螺纹 公差 Buttress threads with 3 and 30 degrees flank angle—Tolerances
139 GB/T 13823.10-1995 振动与冲击传感器的校准方法 冲击二次校准 Methods for the calibration of vibration and shock pick-ups--Secondary shock calibration
140 GB/T 13921-1992 关于固定结构特别是建筑物和海上结构的居住者对低频(0.063～1Hz)水平运动响应的评价导则 Guidelines for the evaluation of the response of occupants of fixed structures, especially buildings and off-shor structures, to low-frequency horizontal motion (0.063～1Hz)
141 GB/T 14091-1993 机械产品环境参数分类及其严酷程度分级 Classification of environmental parameters and their severities for machinery products
142 GB/T 14092.1-1993 机械产品环境条件 湿热 Environmental condition for machinery products Warm-damp
143 GB/T 14093.1-1993 机械产品环境技术要求 湿热环境用 Environmental technical requirements of machinery products for the warm-damp environments
144 GB/T 14124-1993 机械振动与冲击对建筑物振动影响的测量和评价基本方法及使用导则 Mechanical vibration and shock--Measurement and evaluation of vibration effects on buildings--Guidelines for the use of basic standard methods
145 GB/T 14125-1993 振动与冲击对室内振敏设备影响的测量与数据呈报方法 Vibration and shock sensitive equipment--Methods of measurement and reporting data of vibration and shock effects in buildings
146 GB/T 14412-1993 机械振动与冲击 加速度计的机械安装 Mechanical vibration and shock--Mechanical mounting of accelerometers
147 GB/T 14495-1993 木制件表面粗糙度 比较样块 Roughness comparison specimens for wooden pieces
148 GB/T 14689-1993 技术制图 图纸幅面和格式 Technical drawings--Size and layout of drawing sheets
149 GB/T 14690-1993 技术制图 比例 Technical drawings--Scales
150 GB/T 14691-1993 技术制图 字体 Technical drawings--Lettering
151 GB/T 14692-1993 技术制图 投影法 Technical drawings--Projection methods
152 GB/T 14791-1993 螺纹术语 The terms of screw threads
153 GB/T 15049.3-1996 CAD 标准件图形文件 几何图形和特性规范 铆钉 CAD standard parts file--Specification of geometry and parameters--Revets
154 GB/T 15049.4-1996 CAD 标准件图形文件 几何图形和特性规范 销 CAD standard parts file--Specification of geometry and parameters--Pins
155 GB/T 15049.5-1996 CAD 标准件图形文件 几何图形和特性规范 螺母 CAD Standard parts file--Specification of geometry and parameters--Nuts
156 GB/T 15049.6-1996 CAD 标准件图形文件 几何图形和特性规范 螺栓 CAD Standard parts file--Specification of geometry and paramelers--Bolts
157 GB/T 15049.7-1996 CAD 标准件图形文件 几何图形和特性规范 螺钉 CAD standard parts file--Specification of geometry and parameters--Screws
158 GB/T 15049.8-1996 CAD 标准件图形文件 几何图形和特性规范 挡圈 CAD Standard parts file--Specification of geometry and parameters --Rings
159 GB/T 15049.9-1996 CAD 标准件图形文件 几何图形和特性规范 垫圈 CAD standard parts file--Specification of geometry and parameters--Washers
160 GB/T 15054.1-1994 小螺纹 牙型 Miniature screw threads-Profiles
161 GB/T 15054.2-1994 小螺纹 直径与螺距系列 Miniature scrcw threads--Generat plan
162 GB/T 15054.3-1994 小螺纹 基本尺寸 Miniature screw threads--Basic dimensions
163 GB/T 15054.4-1994 小螺纹 公差 Miniature screw threads--Tolerances
164 GB/T 15054.5-1994 小螺纹 极限尺寸 Miniature screw threads--Limits of sizes
165 GB/T 15706.1-1995 机械安全 基本概念与设计通则 第1部分:基本术语、方法学 Safety of machinery--Basic concept, general principles for design--Part 1: Basic terminology, methodology
166 GB/T 15706.2-1995 机械安全 基本概念与设计通则 第2部分:技术原则与规范 Safety of machinery--Basic concepts, general principles for design--Part 2: Technical principles and specifications
167 GB/T 15751-1995 技术产品文件 计算机辅助设计与制图 词汇 Technical product documentation--Requirements for computer aided design and drafting--Vocabulary
168 GB/T 15754-1995 技术制图 圆锥的尺寸和公差注法 Technical drawings--Dimensioning and tolerancing of cones
169 GB/T 15755-1995 圆锥过盈配合的计算和选用 The calculation and selection of cone interference fits
170 GB/T 15756-1995 普通螺纹 极限尺寸 Limits of size for general purpose screw threads
171 GB/T 15757-1995 表面缺陷 术语 Surface defect terms
172 GB/T 15822-1995 磁粉探伤方法 Methods for magnetic particle testing
173 GB/T 15823-1995 氦泄漏检验 Examination for helium leak detecting
174 GB/T 15830-1995 钢制管道对接环焊缝超声波探伤方法和检验结果的分级 Methods of ultrasonic inspection and result classification of circumferential butt welds in steel pipes and tubes
175 GB/T 16181-1996 爆破片装置夹持器型式和外形尺寸 Bursting disc devices--Type and outline dimensions holders
176 GB 16454-1996 锯床 安全防护技术要求 Sawing machines--Safeguarding specification
177 GB/T 16671-1996 形状和位置公差 最大实体要求、最小实体要求和可逆要求 Geometrical tolerancing--Maximum material requirement,least material requirement and reciprocity requirement
178 GB/T 16673-1996 无损检测用黑光源（UV-A）辐射的测量 Measurement of UV-A radiation (black light) used in non-destructive testing
179 GB/T 16675.1-1996 技术制图 简化表示法 第1部分：图样画法 Technical drawings--Simplified representation--Part 1: Pictorial presentation
180 GB/T 16675.2-1996 技术制图 简化表示法 第2部分：尺寸注法 Technical drawings--Simplified representation--Part 2: Dimensioning
201 GB/T 131-1993 机械制图 表面粗糙度符号、代号及其注法 Mechanical drawings--Surface roughness symbols and methods of indicating
202 GB/T 145-1985 中心孔 Center holes
203 GB/T 157-1989 锥度与锥角系列 Series of conical tapers and taper angles
204 GB/T 192-1981 普通螺纹 基本牙型 General purpose screw threads--Basic concepts and symbols for tooth shapes and tolerance zone
205 GB/T 193-1981 普通螺纹 直径与螺距系列 (直径1~600mm) General purpose screw threads--Diameters and pitches
206 GB/T 196-1981 普通螺纹 基本尺寸 (直径1~600mm) General purpose screw threads--Basic dimensions for diameter from 1 to 600mm
207 GB/T 197-1981 普通螺纹 公差与配合 (直径1~355mm) General purpose screw threads--Tolerances and fits fordiameter from 1 to 355mm
208 GB/T 16948-1997 技术产品文件 词汇 投影法术语 Technical product documentation--Vocabulary--Terms relating to projection methods
209 GB/T 16949-1997 字体和符号模板 基本要求、识别标记及槽宽尺寸 Templates for lettering and symbols--General principles, identification markings and the size of the slot widths
210 GB 11291-1997 工业机器人 安全规范 Industrial robots--Safety specification
211 GB/T 12643-1997 工业机器人 词汇 Industrial robots--Vocabulary
212 GB/T 16977-1997 工业机器人 坐标系和运动命名原则 Industrial robots--Coordinate systems and motion nomenclature
213 GB/T 16978-1997 工业自动化 词汇 Industrial automation glossary
214 GB/T 16979.1-1997 工业自动化系统 制造报文规范 第1部分: 服务定义 补充件1: 数据交换 Industrial automation systems--Manufacturing message specification--Part 1: Service definition AMENDMENT 1: Data exchange
215 GB/T 16979.2-1997 工业自动化系统 制造报文规范(MMS) 第2部分: 协议规范 补充件1: 数据交换 Industrial automation systems--Manufacturing message specification--Part 2: Protocol specification AMENDMEN 1: Data exchange
216 GB/T 16980.1-1997 工业自动化 车间生产 第1部分: 标准化参考模型和确定需求的方法论 Industrial automation--Shop floor production--Part 1: Reference model for standardization and a methodology for identification of requirements
217 GB/T 16980.2-1997 工业自动化 车间生产 第2部分: 标准化参考模型和方法论的应用 Industrial automation--Shop floor production--Part 2: Application of the reference model for standardization and methodology
218 GB/T 8129-1997 工业自动化系统 机床数值控制 词汇 Industrial automation systems--Numerical control of machines--Vocabulary
219 GB/T 15049.10-1997 CAD标准件图形文件 几何图形和特性规范 键 CAD standard parts file--Specification of geometry and parameters--Key
220 GB/T 15049.11-1997 CAD标准件图形文件 几何图形和特性规范 滚动轴承 CAD standard parts file--Specification of geometry and parameters--Rolling bearings
221 GB/T 4459.7-1998 机械制图 滚动轴承表示法 Mechanical drawings--Representation of rolling bearings
222 GB/T 1800.2-1998 极限与配合 基础 第2部分: 公差、偏差和配合的基本规定 Limits and fits--bases--Part 2: Basic rules of tolerances,deviations and fits
223 GB/T 1800.3-1998 极限与配合 基础 第3部分: 标准公差和基本偏差数值表 Limits and fits--bases--Part 3: Numerical values tables of standard toleranes and fundamental deviations
224 GB/T 17450-1998 技术制图 图线 Technical drawings--Basicc conventions for lines
225 GB/T 17451-1998 技术制图 图样画法 视图 Technical drawings--General principles of presentation--Views
226 GB/T 17452-1998 技术制图 图样画法 剖视图和断面图 Technical drawings--General principles of presentation--Sections and cuts
227 GB/T 17453-1998 技术制图 图样画法 剖面区域的表示法 Technical drawings--General principles of presentation--Representation of areas on cuts and sections
228 GB/T 17454.1-1998 机械安全 压敏防护装置 第1部分: 压敏垫和压敏地板设计和试验通则 Safety of machinery Pressure sensitive protective device Part 1: General principles for the design and testing of pressure sensing mats and pressure sensing floors
229 GB/T 17455-1998 无损检测 表面检测的金相复制件技术 Non-destructive testing--metallographic replica techniques of surface examination
230 GB/T 8069-1998 功能量规 Functional gauges
231 GB/T 14665-1998 机械工程 CAD制图规则 Mechanical engineering drawings rules of CAD
232 GB/T 1181-1998 过盈配合螺纹 The interference-fit threads
233 GB/T 10610-1998 产品几何技术规范 表面结构 轮廓法评定表面结构的规则和方法 Geometrical product Specifications(GPS)-Surface texture:Profile method-Rules and procedures for the assessment of surface texture
234 GB/T 11348.1-1999 旋转机械转轴径向振动的测量和评定 第1部分：总则 Mechanical vibration of non-reciprocating machines--Measurements on rotating shafts and evaluation criteria--Part 1: General guidelines
235 GB/T 11348.3-1999 旋转机械转轴径向振动的测量和评定 第3部分：耦合的工业机器 Mechanical vibration of non-reciprocating machines--Measurements on rotating shafts and evaluation criteria Part 3: Coupled industrial machines
236 GB/T 11348.4-1999 旋转机械转轴径向振动的测量和评定 第4部分：燃气轮机组 Mechanical vibration of non-reciprocating machines--Measurements on rotating shafts and evaluation criteria--Part 4: Gas turbine se
我们是知识搬运工，我们是技术传播者！
东莞潇洒职业培训学校目前开设课程有：学历提升、积分入户、数控编程培训、塑胶模具设计培训，压铸模具设计培训、冲压模具设计培训，精雕、ZBrush圆雕培训、Solidworks产品设计培训、pro/E产品设计培训、AutoformR7工艺分析培训，非标自动化设计、PLC编程、工业机器人、CNC电脑锣操机、平面设计等培训课程，潇洒职业培训学校线下、线上等网络学习方式，随到随学，上班学习两不误，欢迎免费试学！
线上免费试学： xsmj.ke.qq.com
联系电话：18029183887（微信同号）QQ：2958861564
学校官网：www.dgxspx.com 智造人才网:www.58hr.net
学习地址：东莞市横沥镇新城工业区兴业路121号－潇洒职业培训学校
